2 to 12 gang Terminal blocks
Used to interface between your switch panel and boat’s wiring harness.
Echo Warm White
1 × $42.89
AT06-12SA, 12-Way Plug
1 × $4.30
Hatch Up/Down
1 × $81.00
Light Port/Stbd
1 × $81.00
Blue Sea 5511e e-Series Dual Circuit Plus Battery Switch
1 × $66.00
Jack Plate Up/Down
1 × $81.00
EGIS XD Flex Triple - ACR/RBS w/Knob
1 × $350.00
Blue Sea 6011200 ON-OFF-COMBINE
1 × $57.50
Mini Add-A-Battery Kit 65A
1 × $152.00
250A MEGA or AMG Fuse
1 × $10.59
Auto Pilot – Right
1 × $25.99
Dimmer
1 × $8.99
Blower
2 × $8.99
Andros Warm White White Housing
1 × $33.89
50 Amp MIDI/AMI Fuse - 2 Pack
1 × $8.29
Bilge Man/Auto
2 × $8.99
AT06-2S, 2-Way Plug
1 × $1.10
Battery Para
1 × $8.99
Bluewater 1-2-BOTH Battery Switch
1 × $49.00
Lights Vertical Port/Stbd
1 × $81.00
19mm Dimmer Combo
1 × $58.00
Wedgelock for ATP04-4P
1 × $0.50
Negative Bus Bar - 10 Circuit
1 × $20.00 Subtotal: $1,257.99
$4.99 – $15.00Price range: $4.99 through $15.00
2 to 12 gang Terminal blocks
Used to interface between your switch panel and boat’s wiring harness.
Fast Shipping
Expert Support
Easy Returns
Our fully wired switch panels are meant to terminate onto one of these marine terminal blocks. They are a handy way to break circuits out and troubleshoot electrical issues.
We carry 2, 4, 6, 8, 10, and 12 circuits, or “gang” terminal blocks. Each gang is isolated… so only the adjacent screw is connected.
So your switch panel ring terminals would go on one side, and the load wiring going out to your device would be landed on the other side. This is distinctly different than a Marine bus bar where all the wires are grouped together. We also carry the bus bar which you’ll need for the negative side of the circuit.
Our terminal blocks are rated for 30A per circuit, and 600V. They have Nickel-Plated Brass Contacts. They use a #8 sized ring terminal.
If purchasing to interface your New Wire Marine switch panel, you’ll need:
Example 1:
You have 9 switches. Two are DPDT (the Nav/Anc and the Livewell/Aerator). So you’d need 1 primary input, 2 for the Nav/Anc, and 2 for the Livewell, then 1 more for the other 7 switches. That’s 1 +2 + 2+ 7 = 12 circuits. So you’d need a 12 gang terminal block.
Example 2:
You have 12 switches. One is a Nav/Anc and 4 of them are sending power to 3 night fishing lights each (12 lights total). So you’ll need 1 primary input, 2 for the nav/anc, 12 for the night fishing lights, then 7 for all the other switches. That’s 1 + 2 + 12 + 7 = 22 circuits total. So you’d need at least one 10 post and one 12 post. Or maybe two 12 in-case you forgot something or want to add something later.
Also, you can double up on the same screw. Makes it not quite as clean-looking, but it can cut down on the space needed for lots of circuits.
We’ve included a diagram below on how our marine terminal blocks are used in a typical boat’s electrical system.
